Free referral line · Independent guides, every cost sourced Calls answered 24/7 for water emergencies · 1-800-555-0199

Basements & Crawl Spaces · Guide

Crawl Space Vapor Barrier Installation

Crawl space vapor barrier installation: what thickness to choose (6, 10, 12 or 20 mil), the best vapor barrier for a crawl space, how it's installed, and cost.

Short answer

A crawl space vapor barrier (installation covered below) is polyethylene sheeting that covers the dirt floor (and in encapsulation, the walls) to stop ground moisture evaporating into the crawl space. Thicker is tougher: 6 mil is a code-minimum style ground cover, while 12 to 20 mil reinforced liners resist tears from foot traffic. Material runs roughly $0.05 to $0.60 per sq ft by thickness; installed, a basic barrier costs about $2 to $4 per sq ft.

Bare soil releases a surprising amount of moisture into a crawl space. A vapor barrier is the cheapest single step to cut it, and it's the foundation of full encapsulation.

Crawl space vapor barrier thickness

Thickness Typical use Notes
6 mil Basic ground cover Tears easily with traffic
10 – 12 mil Ground cover with some traffic Common middle choice
20 mil (reinforced) Encapsulation, storage, frequent access Most durable; costs more

Material prices by thickness run from about $0.05–$0.20 per sq ft for thin sheeting to $0.40–$0.60 per sq ft for 20 mil (This Old House).

What's the best vapor barrier for a crawl space?

  • Reinforced (string- or mesh-reinforced) polyethylene resists punctures.
  • Thicker liners (12 to 20 mil) hold up better where people crawl.
  • Lighter colors make inspection easier.
  • Taped seams and sealed edges matter as much as thickness.

Crawl space vapor barrier installation

  1. Fix water problems first. See water in the crawl space.
  2. Clear debris and sharp objects; level rough spots.
  3. Lay sheets with generous overlaps (often 12 inches or more).
  4. Tape seams with compatible tape.
  5. Run up the walls and fasten, for encapsulation.
  6. Seal around piers and pipes.
  7. Inspect for tears after any service work.
A vapor barrier covers the soil so ground moisture can't evaporate into the crawl space.

Crawl space moisture barrier cost

Item Typical cost
Barrier material (6 to 20 mil) ~$0.05 – $0.60 per sq ft
Installed vapor barrier $2 – $4 per sq ft
Typical project $1,200 – $4,000

Sources: This Old House, Angi.

Pro tip

A barrier alone doesn't dry a humid crawl space if the vents keep pulling in muggy summer air. If the space still smells musty after a barrier, the next step is sealing vents and adding a dehumidifier.

Vapor barrier mistakes to avoid

  • Gaps at walls and piers that let moisture escape around the barrier.
  • Thin sheeting in a crawl space people need to crawl through.
  • No tape at seams.
  • Laying it over standing water without fixing drainage.
  • Covering foundation vents without a plan for humidity.

Vapor barrier vs encapsulation: which do you need?

Situation Usually enough
Dry climate, dry crawl space, no smell Vapor barrier
Humid climate, musty smell Encapsulation
Mold on joists Remediation plus encapsulation
Standing water Drainage first, then barrier or encapsulation

How much vapor barrier do you need?

Measure the crawl space floor area and add extra for overlaps and, for encapsulation, the walls and piers:

  1. Floor: length x width.
  2. Overlaps: add roughly 10% to 15% for seams.
  3. Walls (encapsulation): perimeter x wall height.
  4. Piers: each pier's perimeter x height.

Illustration only: a 40 x 30 ft crawl space has 1,200 sq ft of floor. With overlaps, that's roughly 1,350 sq ft of liner for the floor alone. Running 3 ft up 140 ft of perimeter adds about 420 sq ft more.

Vapor barrier and building codes

Many US codes allow unvented crawl spaces when the ground is covered with a vapor retarder, seams are overlapped and sealed, the liner runs up the walls, and the space is conditioned or dehumidified. Requirements vary by jurisdiction and adoption year, so ask your contractor or local building department before sealing vents.

Signs your existing vapor barrier is failing

  • Tears, gaps or sections pulled away from walls.
  • Water pooling on top of the liner.
  • Musty smell returning to the house.
  • Mold on joists above the liner.
  • Liner buried under debris or old insulation.

Frequently asked questions

What thickness vapor barrier for a crawl space?

6 mil is a minimum; 12 to 20 mil reinforced liners are more durable and common for encapsulation.

Is a 20 mil crawl space vapor barrier worth it?

If people will crawl on it or store things, yes. It resists tears much better.

How much does crawl space vapor barrier installation cost?

About $2 to $4 per sq ft installed, often $1,200 to $4,000 total.

Does a vapor barrier stop crawl space mold?

It reduces ground moisture, which helps, but humid air and leaks also need to be controlled.

Can I install a crawl space vapor barrier myself?

Many homeowners do for a simple floor barrier. Crawl spaces with low clearance, mold or water are often better left to pros.

How long does a crawl space vapor barrier last?

A heavy, undamaged liner can last many years; thin sheeting tears and degrades sooner.

Should the vapor barrier go up the crawl space walls?

For encapsulation, yes. A floor-only barrier is simpler but leaves the walls and vents uncontrolled.

Can a vapor barrier be installed over gravel?

Yes. Smooth or remove sharp stones first and consider a thicker, reinforced liner.

Crawl space vapor barrier installation is quick for a pro and lasts for years when it's done right. Call the number on this page and we'll connect you with a participating local installer.

Expert review: pending Waterproofing reviewer
Required credential:Basement Health Assoc. certified

Written and fact-checked by DryLevel editors, last updated 2026-11-16. Costs come from the sources linked in the article. Read our editorial policy or report a correction.

Call 1-800-555-0199