Helical piers are steel shafts with screw-like plates that are turned into the ground until they reach a set torque, then bracketed to the foundation. Push piers are steel tubes driven down using the weight of the house until they hit load-bearing soil or rock. Concrete piers are pressed or poured cylinders. Angi puts typical costs at about $1,000 (concrete), $2,000 (push) and $3,000 (helical) per pier, and most homes need several.
Piers are how settled foundations are stabilized and, often, lifted back toward level. They move the weight of the house off weak soil near the surface and onto stronger soil or bedrock deeper down. If a contractor recommends foundation piering, the questions to ask are which pier type, how many, how deep, and what the warranty covers.
Helical piers vs push piers vs concrete piers
| Helical piers | Push piers | Concrete piers | |
|---|---|---|---|
| How installed | Screwed in with hydraulic torque | Driven down using the home's weight | Pressed segments or poured in place |
| Best for | Lighter homes, slabs, porches, new additions | Heavier homes with deep, firm bearing layer | Areas with shallow firm soil |
| Load check | Torque reading during install | Hydraulic pressure during install | Depth and pressure (segmented) |
| Typical cost per pier | ~$3,000 | ~$2,000 | ~$1,000 |
Costs: Angi. Angi's underpinning guide gives averages of $1,700 (segmented concrete), $2,100 (concrete), $2,700 (push/steel) and $3,500 (helical) per pier (Angi).
How helical pier installation works
- Dig a small access hole at the footing at each pier location.
- Screw the helical shaft into the soil with a hydraulic drive head, adding extensions until it reaches the specified torque.
- Attach a steel bracket to the footing.
- Transfer load: the house is tied to the pier and, where planned, lifted gradually across several piers at once.
- Backfill and record each pier's depth and torque.
Push piers follow a similar pattern, except the pier is hydraulically pushed down, using the house as the counterweight, until it hits refusal.
How many piers does a house need?
It depends on how much of the foundation moved and the engineer's load calculation. Spacing is often in the range of every 5 to 8 feet along the affected wall. Angi notes that a typical underpinning job uses around 10 piers, which is why full-perimeter jobs land in five figures.
Foundation piering cost
| Scope | Typical cost |
|---|---|
| Per pier (concrete / push / helical) | ~$1,000 / ~$2,000 / ~$3,000 |
| Piering or underpinning, per pier | $1,000 – $3,000 |
| Full underpinning project (about 10 piers) | $10,000 – $30,000 |
Sources: Angi, This Old House.
Ask for the install log. Good contractors record the depth and final torque or pressure of every pier. That log, plus a transferable warranty, is what a future buyer's inspector will want to see.
Questions to ask before you sign
- Why this pier type for my house and soil?
- How many piers, where, and was that sized by an engineer?
- Are you lifting the house or just stabilizing it?
- What happens to plumbing and finishes during a lift?
- Is the warranty transferable, and what exactly does it cover?
Steel pier vs concrete pier: the durability question
Steel push and helical piers are typically galvanized and installed to a verified load (pressure or torque), and are often sold with long transferable warranties. Pressed concrete piers are cheaper but depend more on soil friction and installation depth. In areas with deep firm soil or bedrock, steel piers reach it; in areas with shallow firm soil, concrete piers can work well.
How long foundation piering takes
| Job | Typical time on site |
|---|---|
| A few piers at one corner | 1 day |
| One full wall | 1–2 days |
| Full perimeter | 2–5 days |
Add time for permits, engineering and finish repairs.
Pier warranty fine print
- Does it cover the pier, the lift, or both?
- Is the lift guaranteed to stay, or only the pier to hold?
- Is it transferable, and is there a fee?
- Does it require drainage maintenance by you?
Frequently asked questions
What are helical piers?
Steel shafts with helix plates that are screwed into the soil to a measured torque and then bracketed to the foundation to support it.
Are helical piers better than push piers?
Neither is better everywhere. Helical piers suit lighter structures and are load-tested by torque; push piers suit heavier homes and use the house's weight to drive them to firm soil.
How much do helical piers cost?
Angi puts helical piers at about $3,000 each on average; totals depend on how many are needed.
How long do foundation piers last?
Galvanized steel piers are designed to last decades. Check the manufacturer and contractor warranty terms.
How deep do helical piers go?
Until they reach the target torque in competent soil, which can be anywhere from several feet to much deeper depending on the site.
Do foundation piers need maintenance?
The piers themselves don't, but keeping drainage working around the house protects the repair.
Whether helical piers or push piers suit your house depends on its weight and your soil. Ring the number on this page and a participating local foundation company can tell you which method fits.
Written and fact-checked by DryLevel editors, last updated 2026-11-16. Costs come from the sources linked in the article. Read our editorial policy or report a correction.